Number of teeth on camshaft gear and camshaft drive gear
- whc03grady
- IAC Addict!
- Location: Livingston Montana
- Contact:
- Status: Offline
Number of teeth on camshaft gear and camshaft drive gear
Are the number of teeth on the camshaft gear and on the camshaft drive gear prime?
Ludwig--1974 Westfalia, 2.0L (GD035193), Solex 34PDSIT-2/3 carburetors.
Gertie--1971 Squareback, 1600cc with Bosch D-Jetronic fuel injection from a '72 (E brain).
Read about their adventures:
http://www.ludwigandgertie.blogspot.com
Gertie--1971 Squareback, 1600cc with Bosch D-Jetronic fuel injection from a '72 (E brain).
Read about their adventures:
http://www.ludwigandgertie.blogspot.com
- SlowLane
- IAC Addict!
- Location: Livermore, CA
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
Well, the camshaft gear can't be, because it has to have exactly twice the number of teeth as the drive gear.whc03grady wrote: ↑Tue Oct 29, 2019 12:04 amAre the number of teeth on the camshaft gear and on the camshaft drive gear prime?
'81 Canadian Westfalia (2.0L, manual), now Californiated
"They say a little knowledge is a dangerous thing, but it is not one half so bad as a lot of ignorance."
- Terry Pratchett
"They say a little knowledge is a dangerous thing, but it is not one half so bad as a lot of ignorance."
- Terry Pratchett
- asiab3
- IAC Addict!
- Location: San Diego, CA
- Contact:
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
Thanks SlowLane. I had a long reply typed up on my phone and fell asleep on it... That saved me a lot of math and editing :)
Mitch, why do you ask? :)
Robbie
Mitch, why do you ask? :)
Robbie
1969 bus, "Buddy."
145k miles with me.
322k miles on Earth.
145k miles with me.
322k miles on Earth.
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
whc03grady wrote: ↑Tue Oct 29, 2019 12:04 amAre the number of teeth on the camshaft gear and on the camshaft drive gear prime?
52 Cam 26 Crank. I counted them when I had to file each and every one of them on Chloe's engine ...
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- whc03grady
- IAC Addict!
- Location: Livingston Montana
- Contact:
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
Right. <slaps forehead>
Because if they are prime (or even relatively prime), a given tooth on one won't regularly contact a given tooth on the other, thereby potentially reducing wear.
I wish the crank teeth were lettered A-Z.
Ludwig--1974 Westfalia, 2.0L (GD035193), Solex 34PDSIT-2/3 carburetors.
Gertie--1971 Squareback, 1600cc with Bosch D-Jetronic fuel injection from a '72 (E brain).
Read about their adventures:
http://www.ludwigandgertie.blogspot.com
Gertie--1971 Squareback, 1600cc with Bosch D-Jetronic fuel injection from a '72 (E brain).
Read about their adventures:
http://www.ludwigandgertie.blogspot.com
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
VW floats a number of components to reduce wear.whc03grady wrote: ↑Mon Nov 04, 2019 7:19 pmBecause if they are prime, a given tooth on one won't regularly contact a given tooth on the other, thereby potentially reducing wear.
a) distributor drive gear has a spring (YOU KNOW THIS) that allows the brass gear and pinion to vary their contact.
b) valves and lifters are designed to rotate in operation to spread the wear
c) piston rings are invited to rotate slowly with honing patterns that have just a tad of "english"
d) a generous .016" float between the rods and the crank journals and full-floating wrist pins
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- SlowLane
- IAC Addict!
- Location: Livermore, CA
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
Again, because the cam:crank rotational ratio must be 1:2, there is no choice but for the same teeth to meet every revolution. As to the actual number of teeth used, I suspect things like strength of materials and tooling constraints ( ie. if the cam/ crank gear teeth are the same size as the teeth on other gears elsewhere, that may help with production efficiencies) to be predominant.whc03grady wrote: ↑Mon Nov 04, 2019 7:19 pmBecause if they are prime (or even relatively prime), a given tooth on one won't regularly contact a given tooth on the other, thereby potentially reducing wear.
'81 Canadian Westfalia (2.0L, manual), now Californiated
"They say a little knowledge is a dangerous thing, but it is not one half so bad as a lot of ignorance."
- Terry Pratchett
"They say a little knowledge is a dangerous thing, but it is not one half so bad as a lot of ignorance."
- Terry Pratchett
- asiab3
- IAC Addict!
- Location: San Diego, CA
- Contact:
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
I suspect the tooth size was a function of how many teeth were needed to mesh with such consistency that:
A) The camshaft would never have too much backlash
B) Increments could be made (economically) to the gear pitch to allow for crank/cam interface tolerance (+7 to -7 cam gears, 15 in all, for T1's. How many for T4's?)
C) The expansion rate of the dissimilar metals was compatible.
Or something like that.
Robbie
A) The camshaft would never have too much backlash
B) Increments could be made (economically) to the gear pitch to allow for crank/cam interface tolerance (+7 to -7 cam gears, 15 in all, for T1's. How many for T4's?)
C) The expansion rate of the dissimilar metals was compatible.
Or something like that.
Robbie
1969 bus, "Buddy."
145k miles with me.
322k miles on Earth.
145k miles with me.
322k miles on Earth.
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
Oh my ...asiab3 wrote: ↑Fri Nov 08, 2019 12:20 amI suspect the tooth size was a function of how many teeth were needed to mesh with such consistency that:
A) The camshaft would never have too much backlash
B) Increments could be made (economically) to the gear pitch to allow for crank/cam interface tolerance (+7 to -7 cam gears, 15 in all, for T1's. How many for T4's?)
C) The expansion rate of the dissimilar metals was compatible.
Or something like that.
Robbie
Packaging constraints on the one side, shear strength of magnesium/aluminum on the other. Helical cut at best achievable angle for quiet without drilling the camshaft through the ends of the engine, all of these considerations.
It is interesting to consider if any considerations were given to gear design size to control the range of mesh clearance through temperature range, but I am pretty sure they just said "f**ket, this thing is so damn noisy anyway, we just need a quiet mesh at warm idle." And that is exactly how it works out at "0" clearance cold.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- asiab3
- IAC Addict!
- Location: San Diego, CA
- Contact:
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
I would love to believe that. 71whitewesty's SnoCat 1600 single port reminded me how quiet you can really get these things with a long enough exhaust! Like a late bus…
I was just thinking that Buddy's engine was sounding rather magnificent, until I pulled up to a friend's house with a fresh hydraulic lifter Type 4, full of perfectly sealed NOS exhaust parts Even our smog tech commented on the note… (Which is a brief dopamine rush until one realizes what it says about the state of our hobby community…)
1969 bus, "Buddy."
145k miles with me.
322k miles on Earth.
145k miles with me.
322k miles on Earth.
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Number of teeth on camshaft gear and camshaft drive gear
asiab3 wrote: ↑Fri Nov 08, 2019 7:30 pmI would love to believe that. 71whitewesty's SnoCat 1600 single port reminded me how quiet you can really get these things with a long enough exhaust! Like a late bus…
I was just thinking that Buddy's engine was sounding rather magnificent, until I pulled up to a friend's house with a fresh hydraulic lifter Type 4, full of perfectly sealed NOS exhaust parts Even our smog tech commented on the note… (Which is a brief dopamine rush until one realizes what it says about the state of our hobby community…)
I like the clattery valve train noise of solid lifter VW engines. And my solid lifter 2.0 sounds better than my hydraulic lifter 2.0 in the cabin.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles