tech bulletin from RAtwell
http://www.ratwell.com/mirror/www.dolph ... hbull.html
Blown Head Gasket Repair at 600 Miles
- sgkent
- Addicted!
- Location: Citrus Heights CA (near Sacramento)
- Status: Offline
Re: Blown Head Gasket Repair at 600 Miles
TBone208 wrote: "You ppl are such windbags. Go use your crystal ball to get rich & predict something meaningful. Nobody knows what's going to happen. How are we supposed to take ppl who don't know the definition of a recession & "woman" seriously?"
Merlin The Wrench
Merlin The Wrench
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Blown Head Gasket Repair at 600 Miles
In reality viewed as:sgkent wrote: ↑Mon May 01, 2017 9:25 amtech bulletin from RAtwell
http://www.ratwell.com/mirror/www.dolph ... hbull.html
1. To eliminate seizing of pistons, increased piston/cylinder clearance from 0.03mm ± 0.008mm to 0.045mm ± 0.005mm.
2. Eliminate aluminum seal 021 101 341A between cylinder and cylinder head.
Eliminate paper gasket 021 101 341A between foot of cylinder and crankcase.
Install 1.6mm aluminum shim 071 101 341, with adhesive D 000 400 at foot of cylinder to compensate for removed paper gasket and aluminum
seal. Illustration 1.
3. To improve heat transfer, oil groves on both sides of the connecting rod to allow oil splash to cool bottom of the piston.
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Blown Head Gasket Repair at 600 Miles
Oh, but it does. Just like when VW used aluminum washer under the TS 2 to **slow down the warm-up**. Customers were complaining about a stumble during warm up. This dumb little washer helped to maintain a slightly richer signal for only a couple of minutes as the engine arrived at operating temperature.
The heat transfer we're talking about as an engine tackles a full-throttle hill is almost momentary but it is critical.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Blown Head Gasket Repair at 600 Miles
Placebo effect. Cost? Nothing. That little washer wasn't a washer but a spacer (022 133 079) and due to it's size (much bigger than a simple thin washer) delayed (1-2mins) heat due to it's size compared to without.Amskeptic wrote: ↑Fri Jun 02, 2017 5:20 amOh, but it does. Just like when VW used aluminum washer under the TS 2 to **slow down the warm-up**. Customers were complaining about a stumble during warm up. This dumb little washer helped to maintain a slightly richer signal for only a couple of minutes as the engine arrived at operating temperature.
The heat transfer we're talking about as an engine tackles a full-throttle hill is almost momentary but it is critical.
Colin
The gasket that was used in the head was very thinly layered aluminum. The layering certainly didn't help retain durability.
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's