Brosol h32/34 pdsi carb

Carbs & F.I.

Moderators: Sluggo, Amskeptic

Post Reply
Blacka1vw
I'm New!
Status: Offline

Brosol h32/34 pdsi carb

Post by Blacka1vw » Wed Jul 15, 2020 3:01 pm

New member here. I’ve been searching trying to find any information on the Brosol h32/34 pdsi carbs. I’m wondering about initial set up and tuning. Thanks
1971 Vw beetle
1971 Vw super beetle
1979 VW Bus
1985 Vw Cabriolet

User avatar
Amskeptic
IAC "Help Desk"
IAC "Help Desk"
Status: Offline

Re: Brosol h32/34 pdsi carb

Post by Amskeptic » Sun Jul 19, 2020 7:22 pm

Blacka1vw wrote:
Wed Jul 15, 2020 3:01 pm
New member here. I’ve been searching trying to find any information on the Brosol h32/34 pdsi carbs. I’m wondering about initial set up and tuning. Thanks
Initial set-up will be found in the '67 and earlier Type 3 manuals. The factory buses use PDSIT carbs which have a central idling circuit grafted on the left carb that routes down to the intake manifolds. That tuning process is described here:

https://itinerant-air-cooled.com/viewto ... =50&t=7767

You CAN use the air synchronization and fuel synchronization procedures in the above article for the PDSI carburetors, but adjust the mixtures to best idle.
Colin
BobD - 78 Bus . . . 112,660 miles
Chloe - 70 bus . . . 206,845 miles
Naranja - 77 Westy . . . 118,840 miles
Pluck - 1973 Squareback . . . . . . 55,570 miles
Alexus - 91 Lexus LS400 . . . 89,009 miles

Blacka1vw
I'm New!
Status: Offline

Re: Brosol h32/34 pdsi carb

Post by Blacka1vw » Mon Jul 20, 2020 5:21 am

Thanks for the reply. This site is incredible and I really appreciate the information that’s available on here and I love what you guys are doing. Gotta get in line for a home visit. I have been studying the above procedure as well as the Bentley and the ratwell. Comparing my carbs to the procedure. I think I got a game plan. I have the later dual carb linkage I believe. It uses the adjustable rods on both ends. A few other things got me kinda puzzled too. In the procedures for the pdsit carbs I read about setting the throttle plates choke open and also a choke closed setting. The new carbs don’t have the adjustable link between the choke and the throttle plate it’s just set so not much adjustment there on the choke open setup Bentley says adjust gap and secure the stop screws with caps I’m not sure what screws it’s referencing. I have a set of 32/34pdsit and the h32/34 pdsi carbs here that I’m studying. Setup will be going on a 1700 stock motor in place of the center mount. More to come...
1971 Vw beetle
1971 Vw super beetle
1979 VW Bus
1985 Vw Cabriolet

Blacka1vw
I'm New!
Status: Offline

Re: Brosol h32/34 pdsi carb

Post by Blacka1vw » Fri Jul 24, 2020 9:24 am

After more searching I found this
https://www.thesamba.com/vw/forum/viewt ... sc&start=0
It’s mostly type 1 but I believe it’s still useful. The new Brosol carbs I have are set up with the 22mm Venturi. I’m gonna go through my worn out 32-34 pdsit carbs and see what mains and Venturis are inside. Possibly come up with a combination that will be good for stock 1700
1971 Vw beetle
1971 Vw super beetle
1979 VW Bus
1985 Vw Cabriolet

Post Reply