Boots: Clamp or No?

Moderators: Sluggo, Amskeptic

Post Reply
User avatar
Mulcheese
Getting Hooked!
Location: Maple Grove, Mn
Status: Offline

Boots: Clamp or No?

Post by Mulcheese » Sun Sep 03, 2017 12:11 pm

I am done with the new CV and boots all around. I have one final question to complete the project. Do you clamp/zip tie the boot ends? My Lobro boots came with clamps but I have yet to install them because during Colins last visit he recommended that I take off the pip clamps from the boots that were on the van at the time.

Some people say yes some say no, Why?
"attending to things in the moment with curiosity and acceptance."
____________________
82 Vanagon Westy - aka: Honey Badger - "cause she just dont give a ...."

kreemoweet
Getting Hooked!
Location: Seattle
Status: Offline

Re: Boots: Clamp or No?

Post by kreemoweet » Sun Sep 03, 2017 7:49 pm

Some say no clamps because that is what the Bentley service manual specifies for the later-type boots with the integral metal caps.
I also recall seeing somewhere that clamps are not used on later axles that have two ridges between which the small end of the boot resides, as
opposed to axles with a single ridge. The boots seem quite snug enough to me to keep out bad stuff, and it would seem that restraining
them with a clamp could only increase stress on, and therefore rate of deterioration of, the boot.

71whitewesty
Addicted!
Status: Offline

Re: Boots: Clamp or No?

Post by 71whitewesty » Mon Sep 04, 2017 9:19 am

I've been going with no clamps lately. I was using zip ties but I just can't see the reason to use anything at all. They are snug and I've never have had a failure at that area. They always seem to fail in the bellows. Just replaced one after 3 years and 27,000 miles, all the other are still fine on that bus.

User avatar
Amskeptic
IAC "Help Desk"
IAC "Help Desk"
Status: Offline

Re: Boots: Clamp or No?

Post by Amskeptic » Mon Sep 04, 2017 9:30 am

71whitewesty wrote:
Mon Sep 04, 2017 9:19 am
I've been going with no clamps lately. I was using zip ties but I just can't see the reason to use anything at all. They are snug and I've never have had a failure at that area. They always seem to fail in the bellows. Just replaced one after 3 years and 27,000 miles, all the other are still fine on that bus.
I use no clamps until the boots have petrified enough to pull the small end out of the channel. That's about 50,000 miles. Then I ziptie and prepare for a repack.
Reins currently.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles

72Hardtop
Old School!
Location: Seattle, WA./HB. Ca./Shizuoka, Japan
Status: Offline

Re: Boots: Clamp or No?

Post by 72Hardtop » Fri Oct 12, 2018 11:49 pm

No clamps on ends at any time.

Just redid the CV joints on mine and installed Rockford boots (no end clamps) The last time I did them was roughly 20+ years ago. If lubed properly the CV will last a loooooooooooooooooooooooooong time so long as the boot holds up.
Attachments
cv 2.jpg
cv 1.jpg
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's

Post Reply