1971 Super Beetle with original DVDA distributor. I've always assumed the red notch on the left is the 5 degress ATDC mark to use for setting the idle timing. Is that correct? The Bentley says my pulley should only have that one mark, but there is a second set of marks (but not a notch) in yellow as you can see.
1971 1600 Timing Marks
- vwlover77
- IAC Addict!
- Location: North Canton, Ohio
- Status: Offline
1971 1600 Timing Marks
Don
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
- hambone
- Post-Industrial Non-Secular Mennonite
- Location: Portland, Ore.
- Status: Offline
Re: 1971 1600 Timing Marks
I've always timed those with engine at full advance, 30 deg. BTDC with vacuum line plugged. TDC mark at 0 should line up 180 deg. with another mark on the pulley. I've seen so many pulley notches that don't mean a damn thing, so it's better to figure it out yourself. A protractor can help too.
http://greencascadia.blogspot.com
http://pdxvolksfolks.blogspot.com
it balances on your head just like a mattress balances on a bottle of wine
your brand new leopard skin pillbox hat
http://pdxvolksfolks.blogspot.com
it balances on your head just like a mattress balances on a bottle of wine
your brand new leopard skin pillbox hat
- asiab3
- IAC Addict!
- Location: San Diego, CA
- Contact:
- Status: Offline
Re: 1971 1600 Timing Marks
$12 and an hour - http://a.co/8aeOfIX
$70 and five minutes - https://www.cbperformance.com/product-p/1887.htm
There are so many different pulleys from the various years, that I Do Not Guess, Ever.
Robbie
$70 and five minutes - https://www.cbperformance.com/product-p/1887.htm
There are so many different pulleys from the various years, that I Do Not Guess, Ever.
Robbie
1969 bus, "Buddy."
145k miles with me.
322k miles on Earth.
145k miles with me.
322k miles on Earth.
- sgkent
- Addicted!
- Location: Citrus Heights CA (near Sacramento)
- Status: Offline
Re: 1971 1600 Timing Marks
If you have a T1 engine, a magnetic base, a long screwdriver, and a dial indicator you can use the old pulley to determine TDC. Drill a small spot in the center of the screwdriver handle so that the tip of the dial indicator can sit in it. Put #1 on what you think is TDC. Pull the spark plug out gently. Put the screwdriver into the spark plug hole resting on the piston top. Put the dial indicator and magnetic base on the tin etc so that the tip of the dial indicator sits on the screwdriver. Turn the pulley a tiny bit to either side until the dial indicator indicates you are near TDC. Run the piston down .020" in one direction and mark the pulley with a tiny mark. Now run the pulley in the opposite direction until it drops .020" again. (It will rise back to 0 then fall. Make another tiny mark. TDC will be 1/2 way in between. You can use a protractor or degree wheel printed the same size as the pulley to mark 30 BTDC. All that said - the pulley Robbie linked, or any good Gene Berg type marked pulley will save you hours of fussing around with timing marks. The original marks are really only good if one has all the original parts - carb, distributor etc and they want to set the engine to smog specs.
TBone208 wrote: "You ppl are such windbags. Go use your crystal ball to get rich & predict something meaningful. Nobody knows what's going to happen. How are we supposed to take ppl who don't know the definition of a recession & "woman" seriously?"
Merlin The Wrench
Merlin The Wrench
- Randy in Maine
- IAC Addict!
- Location: Old Orchard Beach, Maine
- Status: Offline
Re: 1971 1600 Timing Marks
My 71 Super also had that same pulley setup and the notch was indeed the timing notch at 5º ATDC.
I also timed it at 30º +/- 2º (hoses off and capped) at about 3500 RPMs.
I also timed it at 30º +/- 2º (hoses off and capped) at about 3500 RPMs.
79 VW Bus
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: 1971 1600 Timing Marks
VW distinguished between timing and TDC on the retard-equipped Type 1 engines with a notch for the 5*ATDC position on the inner pulley half and a dimple at "0" on the outer pulley half.
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- vwlover77
- IAC Addict!
- Location: North Canton, Ohio
- Status: Offline
Re: 1971 1600 Timing Marks
I've not been able to detect the dimple. I will check again.....
In any case, it would seem that notch on the inner pulley is indeed the correct mark to use.
In any case, it would seem that notch on the inner pulley is indeed the correct mark to use.
Don
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen