New Owner, 70' Fasty

Fastback, Squareback, Notchback, T-3 Karmann Ghia.

Moderators: Sluggo, Amskeptic

Post Reply
User avatar
wdollie6
Getting Hooked!
Status: Offline

Re: New Owner, 70' Fasty

Post by wdollie6 » Sat May 16, 2020 6:03 am

Guests are never a problem, let me know when your schedule falls in place. The only calendar item for September is my daughter's wedding, if allowable by then...

User avatar
wdollie6
Getting Hooked!
Status: Offline

Re: New Owner, 70' Fasty

Post by wdollie6 » Sat Jun 20, 2020 6:00 am

So started working on reupholstering the rear seats, fun job vs. welding, etc. Waited more than 5 weeks for delivery of TMI square weave (apparently they produce only once they have a confirmed order), product seemed to be okay although difficult to determine until install starts. Unfortunately during install of the rear, back seat found that the fit was not acceptable, not possible to "stretch" to make it work either (it was 85 degrees out at the time). The distance between the vinyl strip (tucks into flange at back top of seat) and the step out on either side of the seat was at least 1.5 to 2 inches short. After doing 3 previous VWs with their product I realize the fit is tight, but never to the point of having to rip the material, obviously stopped short of doing that. To check the issue I attempted to fit the cover installing the bottom first, the fit to step out was perfect but obviously not enough material to tuck the vinyl, confirmed that the cover was made incorrectly.

I checked dimensions against my original (which was dirty but in good shape) and confirmed again that the cover was way too short. Contacted TMI more than a week ago and finally receive a reply that I would be receiving and RMA (a little disappointed that they didn't call to discuss), problem being that I have already installed the arm rest cover which requires poking holes in it for the rod. Hopefully they don't use this as a reason to reject a return as I see no reason to pull the arm rest apart, the fit is okay. I do note that they do not included the weave on both sides of the arm rest like the original, only on the side that shows when the arm is up, I suppose I can live with that.

Will advise as to outcome. Still haven't checked other covers, rear bottom and front seats, hopefully they are okay. Also note that I ordered the carpet from JBugs but it was TMI built. They sent me the entirely wrong carpet set, although I have to say JBugs was very responsive, within a day they shipped out the correct product, including a prepaid return, thank you JBugs.

User avatar
Amskeptic
IAC "Help Desk"
IAC "Help Desk"
Status: Offline

Re: New Owner, 70' Fasty

Post by Amskeptic » Sun Jul 05, 2020 10:42 am

wdollie6 wrote:
Sat Jun 20, 2020 6:00 am
reupholstering the rear seats, product seemed to be okay although difficult to determine until install starts. Unfortunately during install of the rear, back seat found that the fit was not acceptable, not possible to "stretch" to make it work.
I ordered the carpet from JBugs but it was TMI built. They sent me the entirely wrong carpet set, although I have to say JBugs was very responsive, within a day they shipped out the correct product, including a prepaid return, thank you JBugs.

I have found tight dimensions on seat upholstery and decided they were trying to prevent wrinkles or sags. I sit on each surface with all of my weight to compress the springs, then get the attachment points squared away. Are you saying the cut-outs for the hinges were too high up?

TMI ... "annoying customers for over twenty years now!"
BobD - 78 Bus . . . 112,660 miles
Chloe - 70 bus . . . 206,845 miles
Naranja - 77 Westy . . . 118,840 miles
Pluck - 1973 Squareback . . . . . . 55,570 miles
Alexus - 91 Lexus LS400 . . . 89,009 miles

User avatar
wdollie6
Getting Hooked!
Status: Offline

Re: New Owner, 70' Fasty

Post by wdollie6 » Tue Jul 28, 2020 8:01 am

After poor customer response on their part I forced the cover to fit, albeit poorly. Again, not my first rodeo putting fabric on seats so realize that some amount of stretching (using hair dryer) and compressing of springs is necessary. Along the top back of the rear seat the fabric is stretched completely taught, almost to the point of tearing, but is almost 2 inches too short side to side. This caused problems with material availability down the seat toward the bottom which made it almost impossible to fit. I'll add pictures.

Needless to say I am disappointed with TMI, especially after I was willing to provide my originals as patterns so they could get it right. In reality I probably should have waited until the COVID crisis had waned as I am sure they had limited, experienced, man(person)power available to them.

Pictures later today.

User avatar
wdollie6
Getting Hooked!
Status: Offline

Re: New Owner, 70' Fasty

Post by wdollie6 » Wed Jul 29, 2020 8:09 am

Pictures of fit up (or lack thereof) of rear seat covers. As I mentioned the top back of the rear seat was way short which left the material way short to go down the sides. The little step out on the sides of the rear back seat were more than an inch off even after stretching as much as possible (left in sun and used blow dryer on high). At the bottom I had to stretch to the point of failure at the seam because of lack of material. Deep disappointment in the product and the response of the company.

The good news is that the rear seat bottom fit okay, not great, okay. Working on the front seats now, hoping for the best, expecting less.

Sewfine will be my go to upholstery company in the future.
Attachments
20200709_104321.jpg
Bottom Tears Caused by Force Fit
20200709_104321.jpg (318.87 KiB) Viewed 178 times
20200709_104325.jpg
Bottom Tears Caused by Force Fit
20200709_104325.jpg (339.66 KiB) Viewed 178 times
20200709_102931.jpg
Right Side Rear "Step"
20200709_102931.jpg (174.9 KiB) Viewed 178 times
20200709_103015.jpg
Left Side Rear "Step"
20200709_103015.jpg (171.3 KiB) Viewed 178 times
20200709_103055.jpg
Left Side, Rear Top
20200709_103055.jpg (183.85 KiB) Viewed 178 times
20200709_103109.jpg
Right Side, Rear Top
20200709_103109.jpg (183.01 KiB) Viewed 178 times

User avatar
wdollie6
Getting Hooked!
Status: Offline

Re: New Owner, 70' Fasty

Post by wdollie6 » Fri Aug 07, 2020 7:41 am

Finally tackled the job I have dreaded since I bought the car, cleaning the undercoating from the frunk. As several suggested gasoline is the best solvent to remove this sticky, gooey mess. I soaked a small area in gas wait 3-4 minutes then wipe with an old cloth (many by the time I was done for the day), worked great with no scraping necessary, however still took several hours. Note, it is a must to be outside when using gas with no loose electrical nearby, battery negative removed of course.

To be able to move the car to the outside I finished up the caliper rebuilds, installed with new rotors and temporarily slapped on the tires. Still have to mount the master cylinder and run hard/soft brake lines but am waiting until I can remove the rest of the undercoating in the area below the fuel tank, maybe later today as more rain is forecasted. For the lower area I plan on cleaning up using a primer, followed by a chassis black type product. Same for the front end components.

My apologies for the lack of pre-clean up pictures.
Attachments
20200807_102343.jpg
20200807_102343.jpg (235.59 KiB) Viewed 32 times
20200807_102303.jpg
20200807_102303.jpg (215.82 KiB) Viewed 32 times
20200807_102337.jpg
20200807_102337.jpg (223.87 KiB) Viewed 32 times

Post Reply